FTTH - Installing fibre optic cable in to the home

CharlieMac

Registered User
Messages
535
I'm thinking of getting Fibre to the Home (FTTH) using the Open eir network and have a few questions about the installation of the fibre cable in to the home.

I assume this will be a hassle and engineers that arrive on the day will have no interest in wasting time so I might be better off arranging a route in to the house myself beforehand.

There is a telegraph pole on the edge of my garden but I don't like the idea of stringing any kind of cable across from there to the house. Many years ago the land line was brought down that pole and buried under the garden and I have no idea how or where but it gets in to the house somehow. I don't think any kind of duct was ever laid down under the lawn back then.

My preference would be to duct the fibre cable under the lawn then there's the matter of getting it in to the house. Including footpath there is about 5-6m distance to reach the desired exit point in a press in the kitchen.

The route would have to go through concrete foundation and concrete ground floor then bend upwards to emerge from the kitchen floor inside a press. That would be my preferred route but it's probably unrealistic.

Another route could be to run cable up the backside of a drain pipe and somehow get under a roof tile in to the attic where I could pull it down to the kitchen... even this way I would need to have an internal vertical duct cut in to the kitchen wall to bring the cable down from the attic neatly to where the current FTTC router is located.

From googling I've seen some cases of two boxes being installed, a thing called a Termination Unit as well as the ONT. Do most people with FTTH only get the ONT or do you sometimes get both?

Did anyone go to any unusual lengths to bring the fibre in to your house to keep everything neat?
 
I was doing a major refurb of my house so when upgrading floor I went to extra effort and I dug a trench in the concrete floor, put in 2 no. 110mm dia pipe ducts from the utility room to outside, put new concrete before new floor finishes. I was also repaving outside so this allowed me to continue ducts outside to outside lights, sockets and a future car charging point not yet fitted but very easy now to install.

I brought that second fibre duct to almost the front boundary when the old copper internet came in. All this was a massive amount of prep work but when the EIR engineer came out everything was so quick and painless.

Whatever your route, if you've the prep work done and the route well worked out that's where it will be put.

I don't fully understand what both those two boxes do, not do I care much if I'm honest, but I have both and yes they don't turn off.
 
From googling I've seen some cases of two boxes being installed, a thing called a Termination Unit as well as the ONT. Do most people with FTTH only get the ONT or do you sometimes get both?
Both would be the norm. Like this.
1000022728.webp
 
Yes from my reading around feels like I will need to take a lead with preparing things so it gets installed how I want it to be including getting ducting and sockets installed in advance and on the day pulling cables in the attic myself because they won't do that either. I thought that Termination Point was for new builds only, it seldom gets mentioned in posts I've read anyway. Maybe it goes unnoticed or it gets installed outside.
 
I thought that Termination Point was for new builds only
I got fibre installed last year for the first time in my 30 year old house and they (OpenEir/KN Circet) had to bring the fibre cable from the pavement into the house (via a hole that they drilled beside the front door) and they installed both the TP and ONT.
 
You need to know where the cable is likely to come from once it reaches your property. Have a room near there where it will reach the house.

When I got SIRO, the cable was pulled to the electric meter box. There was only 5m of fiber left when it reached the electric meter. The ONT box had to be placed within 5m of that location (inside the house).

They are likely to want to pull the fiber cable themselves and install the ONT somewhere that they have enough fiber to reach. The may pull it through convenient ducting. You need a plug near where you want the ONT installed.

The output from the ONT is often just a single 2.5Gbps ethernet port. They will generally say that you can't move the fiber or the ONT once installed and both remain their property.

If you have ethernet cables to multiple rooms in the house, then it matters less where the actual box is placed. It might be worth setting that up before they arrive and it has nothing to do with them.

You can even place the router in a whole different room if you have proper ethernet cabling.

You may be able to use your own router, depending on ISP.

If not, make sure the one they provide has two 2.5Gbps LAN ports, or you will be limited to 1Gbps internet for your LAN.
 
If you have ethernet cables to multiple rooms in the house, then it matters less where the actual box is placed. It might be worth setting that up before they arrive and it has nothing to do with them.
Yeah this is what I'm starting to think myself. The main problem is not the internet speed but the terrible wifi access throughout the house due to size, shape and concrete walls. Also and lack of fixed network points to feed direct in to TVs or a work area to facilitate working from home. Maybe I'll contact a home networking installer and ask them to survey the place all that stuff and APs in the ceilings. More reading and googling to come... MESH networks, Ubiquity and beyond...
 
Maybe I'll contact a home networking installer and ask them to survey the place all that stuff and APs in the ceilings.

If they are surveying, make sure you estimate where the box would go.

I would say that ideally you want an actual ethernet cable from wherever the box is placed to your computer/study. Though the more rooms that are wired the better :) . Wifi can be used for less important connections.

If internet speed is not the actual issue, then as you say, internal connectivity is the limiting factor.
 
If they are surveying, make sure you estimate where the box would go.
Considering putting the TP/ONT and a switch in the attic. With router in Kitchen two floors below. Would make it easier to send cables around the house. From my reading around this may or may not be safe. Most opinions seem be in from countries with hot summers. But attics don't get too hot in summer in this country I don't think and it's a north facing house. There's access via an attic ladder. There are probably mice and a lot of dust up there.
 
Considering putting the TP/ONT and a switch in the attic
That depends on how much fiber length you have available and the willingness of the installers to run it through ducting.

They could potentially run it to the attic externally.

Another option would be to have ethernet cables running to a central room. The room with the ONT could have 2 cables (to/from the central location). You put the router in the central location (or a switch). This means you have access to the router without having to climb into the attic.
 
the willingness of the installers to run it through ducting.
To me this is the big question. I suspect that the guys doing this want as little hassle and cable usage as possible. I doubt that they're going to go out of their way to facilitate lengthy or complex installations.
 
To me this is the big question. I
It is also often a multi-stage process.

The first step is the survey. If you speak with that guy, he can give you an indication of where they are likely to be able to put the ONT.

That will allow you to be ready to negotiate with the next step where they actually pull the cable.
 
In my experience there's no pre-installation "survey" or multi-stage process.
They arrive on the day and want to install it as quickly, simply, and cheaply as possible.
 
The guys that call to your house will only be interested in doing a simple install, they will try and accommodate something's
but I doubt very much a complicated install through concrete floors and kitchen presses would be in their remit
All their paid for is to get the fibre from the road to just inside your house as quickly as possible

Where does you house phone or BB router plug into in your house, that's probably close to the entry point for FTTH??
 
I have finally taken the plunge and ordered FTTH. There is now a large coil of fibre at the gable end of the house and another crew have to come and bring that in to the house. I expect they will follow the same/similar path that the copper "Telecom" line takes in to a crawlspace under the dormer roof off a bedroom on the first floor. Due to some re-modelling done to the house in recent years there is no longer a convenient route from that crawlspace to where the "main" phone socket that lives in the kitchen.

I want to install Access Points in the ceilings around the house each connected to Cat 6 back to a switch.

This is where I'm struggling to decide what to do next. I've been researching this a lot. I was all set to have the ONT, Router, Patch Panel, Switch and maybe in time a VOIP box all in the attic at the top of the house. There's a pull down attic stairs so I think it's accessible and it is a central location to pull cables around the house. But just last weekend I went up there, I guess it was 25C outside and it was baking up there.

Most of the year its not hot at all up there. Then again I never continually monitored the air temp up there so I don't really know. I can't think of any other convenient, centrally located places anywhere else in the house to have this gear.

Which of my listed devices are OK to have in an attic? Maybe the ONT and router could go on a small plywood vertical mount in the crawlspace off the first floor bedroom, it was less hot in there and it's a bit more accessible but very cramped. Then run Cat 6 from there to the attic where the patch panel/switch could be?

Any ideas much appreciated.
 
I did exactly as you suggested - all equipment in the attic and network cables coming back to there from various wireless access points. I would 100% to this again, everything is out of the way but still accessible by pull down ladder for the once a year I might need to power something on/off. Been like that nearly 10 years, no issues with heat.
 
I expect they will follow the same/similar path that the copper "Telecom" line takes in to a crawlspace under the dormer roof off a bedroom on the first floor.
I'd be very surprised if they did this, my understanding as posted above is their job is only to get fibre from outside to inside
And they will do this as quickly and cleanly as possible by running the cable on the outside of your property front, back or side and into the room where you want the modem placed which has to be beside socket preferably a double

Maybe try and have a chat with the company doing the instal to see what your instal options are
 
Last edited:
Agree with @Cervelo above, most installers will refuse to enter a crawl space or attic now claiming their insurance no longer allows them to do so. They may agree to allow you pull the cable in the awkward spaces and have them terminate connections by the attic hatch. If they do so and leave some additional length in the cables you could fix all in position later.

If you remove the insulation below where you're siting them in the attic and insulate around and over them they'll stay a little cooler on the hot days.
 
I have the same set up as @Zenith63 above.

When the installer called, I told him that the cable needed to go to the attic, via a duct that was built into the house. The attic is floored and lighting / power etc, but I told the installer that I would pull the cable into the attic, if he fed it into the ducting. Offer of a tea / coffee etc, goes a long way and he was happy to set everything up in the attic once the cable was pulled in. He made a few recommendations on the set up that I had - I had a network switch in place there to feed the various rooms. I might have been lucky with my installer - others in the local area just got a hole drilled into the TV room and all done there, even though they had the same ductng in place.
 
  • Like
Reactions: Leo
Back
Top